Product index
43020
|
Product number
TE2236
|
Product name
HIGH PERFORMANCE EPOXY PRIMER/TOPCOAT
|
Product group
1
|
Summary code
EE
|
Product description
A high performance, multipurpose, surface tolerant, two-component chemically cured epoxy semi-gloss coating.
|
Uses
Termapoxy TE2236 Epoxy is a true universal coating. Excellent for use on water tanks and any other water containment structures offering cargo, chemical, fuel, and solvent resistance. See the Tank Lining Chemical Resistance Table for specific information. Also used on structural steel, equipment, piping, and masonry at pulp and paper mills, chemical and fertilizer plants, sewage treatment plants, tank farms, and on bridges. Performance alternate for Federal Specifications Mil-P-23236B(SH)-Type I & IV, Type I & IV, and Class 2. Also used on grain cargo. Suitable for use on structural surfaces or surfaces where there is a possibility of incidental food contact in commercial food preparation establishments, food processing plants and federally inspected meat and poultry plants.
|
Advantages
- Low VOC
- Outstanding corrosion protection
- Suitable for salt & fresh water immersion
- Resistant to many solvents and chemicals
- Resistant to cathodic disbondment
- Lowers cost of surface preparation
- Surface tolerant
- Good adhesion to damp surfaces and tight rust
- Low temperature cure to 0°F (-18°C)
- Fast dry-to-recoat
- Self-priming for steel & masonry substrates
|
Chemistry + solvents
MBB proprietary high performance epoxy resin
|
System solvent
TE-10 Thinner
|
Color
Off White (tintable to light pastel colors only), ready-mixed colors
|
Gloss
Semi-Gloss at 60°
|
Mix ratio
4 (base): 1 (converter) see mixing instructions.
|
Viscosity
Variable
|
Solids by weight
86.063 %
|
Solids by volume
80%
|
Density
NA
|
Volatile Organic Compounds (VOC)
1.41 lbs./gal. (170 g/L) varies with color
|
Sag resistance
NA
|
Dry Film Thickness (DFT)
4.0-8.0 mils (100-200 microns) dry 5.9-11.7 mils (147-293 microns) wet. (Make allowances for loss due to overspray & irregular surfaces.)
|
Spread rate
At (25 microns) or (1 mil) DFT1283 sq. ft./gal. (31.5 m2/L)
|
Dry time
At 6 mils (150 microns) DFT
Substrate Temp 20°F (-7°C) 40°F (4°C) 60°F (16°C) 80°F (27°C)
Minimum Recoat 26 Hours 9 Hours 5 Hours 3.5 Hours Dry Hard 53 Hours 17 Hours 10 Hours 7 Hours
Warning: The above table provides general guidelines only. Always consult your Termarust Coatings Specialist for appropriate recoat window since the maximum aged recoat time of this product may be significantly shortened or lengthened by a variety of conditions, including, but not limited to humidity, surface temperature, and the use of additives or thinners. The use of accelerators or force curing may shorten the aged recoat of individual coatings. The above recoat windows may not apply if recoating with a product other than those listed above. If the maximum aged recoat window is exceeded, please consult your Termarust Coatings Specialist for appropriate recommendations to enhance adhesion. Failure to observe these precautions may result in inter coat delamination.
|
|
Working pot life
4 hours @ 77°F (25°C) & 50% R.H.
|
Performance data
HARDNESS (ASTM D 3363, 7 DAY CURE@77°F (25°C): 3H
LIMITATIONS OF USE: Exterior exposure will cause a color change, early dulling, and loss of gloss, but this does not affect the protective properties.
ADHESION (ASTM D 4541): Excellent
SALT SPRAY RESISTANCE: (ASTM B 117): Excellent
ABRASION RESISTANCE: (ASTM D 4060): Good
HUMIDITY RESISTANCE: (ASTM D 2247): Excellent
|
Chemical resistance
Excellent. Resists splash and spillage of alkalis, salts, moisture, oils, greases, foodstuffs and detergents, 50% Sodium
|
Surface preparation
New Surfaces: New steel surfaces should be initially blasted to near-white metal surface
|
Application
Mixing: Termarust TE2236 Coating is a two-component product supplied in 5 gallon and 1 gallon kits which contain the proper ratio of ingredients. The entire contents of each container must be mixed together. Power mix the base portion first to obtain a smooth, homogeneous condition. After mixing the base portion, add the converter slowly with continued agitation. After the converter add is complete, continue to mix slowly. Allow the mixed material to stand 15 minutes at 77°F (25°C) before use. Application: Termarust TE2236 Coating can be applied by air spray and airless spray methods. However, the preferred method of application is with heavy-duty airless spray. For airless application, a 45:1 King pump or larger is recommended. Tip sizes from .021 to .027 will provide a good spray pattern. For optimum results, fluid hoses should be 3/8' ID or larger with a maximum length of 50 feet. Longer hose length or cold temperatures may require an increase in pump ratio and/or thinning. Termarust TE2236 Coating may also be applied by brush or roller. Care should be Surfaces must be dry, clean, free of oil, grease, form release agents, curing compounds, laitance, other foreign matter and be structurally sound. Remove all loose paint, mortar spatter, mill scale, and rust. All direct to metal coatings provide maximum performance over blasted surfaces. There are situations and cost limitations which preclude blasting. Termarust TE2236 was designed to provide excellent protection over less than ideal surface preparation. Flash Point: 100°F (38°C) 5 gallon kit - 70 lbs. (31.8 kg)
|
Application equipment
NA
|
Compatible systems
Ferox 24000 series polyurethane Ferox 76000 series waterbased polyurethane Ferox 1248 Zinc rich primer Termazinc TZ1100 series zinc rich primer
|
Thinning
TE-10 Solvent Thinning is not normally required or desired. However, at lower temperatures, small amounts (10% or less by volume) of the solvents on the reverse page can be added depending on local VOC and air quality regulations. Any solvent addition should be made after the two components are thoroughly mixed. The pot life of the mixed material is 4 hours at 77°F (25°C). Higher temperatures will reduce working life of the coating; lower temperatures will increase it.
|
Clean up
TE-10 Solvent
|
LC50 TROUT 96 HOURS
See MSDS Sheet
|
WEIGHT PER GALLON:
12.9 lbs./gal. (1.5 kg/L) varies with color
|
ELONGATION
N/A
|
INDUCTION
|
OTHER PROPERTIES
PACKAGING: 1 gallon kit (3.785L) 5 gallon kit (18.925L)
TINTING: White can be tinted with CHROMA-CHEM 844 colorants. (Do not use water based colorants). Add colorants to only the base p
SYSTEMS: Please consult the appropriate system guide, the particular job specification or your Termarust Industrial Coating Representative
SERVICE TEMPERATURE LIMITS: 250°F (121°C) dry
Minimum Dry Time (ASTM D 1640): At 6 mils (150 microns) DFT
RECOAT TIMES: Substrate Temp 20°F (-7°C) 40°F (4°C) 60°F (16°C) 80°F (27°C)
Minimum Recoat 26 Hours 9 Hours 5 Hours 3.5 Hours
Dry Hard 53 Hours 17 Hours 10 Hours 7 Hours
Max Recoat Self 30 Days 30 Days 30 Days 30 Days
Ferox 24000 7 Days 6 Days 5 Days 5 Days
|
Shelf life
Over 24 months at 77°F (25°C) unopened
|
Safety precautions & regulatory data
COMBUSTIBLE. HARMFUL OR FATAL IF SWALLOWED. Read label and Material Safety Data Sheet Prior to Use. See other cautions on last page. DANGER! COMBUSTIBLE LIQUID AND VAPOR. CAUSES EYE AND SKIN BURNS. HARMFUL OR FATAL IF SWALLOWED. ASPIRATION HAZARD - CAN ENTER LUNGS AND CAUSE DAMAGE. HARMFUL DANGER!
PRECAUTIONS
DANGER! COMBUSTIBLE LIQUID AND VAPOR. CAUSES EYE AND SKIN BURNS. HARMFUL OR FATAL IF SWALLOWED. ASPIRATION HAZARD - CAN ENTER LUNGS AND CAUSE DAMAGE. HARMFUL IF INHALED. MAY CAUSE CENTRAL NERVOUS SYSTEM EFFECTS, INCLUDING DIZZINESS, HEADACHE OR NAUSEA. CAUSES RESPIRATORY TRACT IRRITATION. MAY CAUSE ALLERGIC SKIN AND RESPIRATORY REACTION. MAY BE HARMFUL IF ABSORBED THROUGH SKIN.
OVEREXPOSURE MAY CAUSE BLOOD, LIVER, KIDNEY DAMAGE. CONTAINS CRYSTALLINE SILICA WHICH CAN CAUSE LUNG CANCER AND OTHER LUNG DAMAGE IF INHALED. CONTAINS MICA WHICH MAY CAUSE PNEUMOCONIOSIS. USE ONLY WITH ADEQUATE VENTILATION. KEEP OUT OF THE REACH OF CHILDREN.
NOTICE: Products in this series contain solvents. Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. For emergency information call (800) 545-2643. Note: These warnings encompass the product series. Prior to use, read and follow product-specific MSDS and label information. Keep away from heat, sparks and flame. Do not smoke. Vapors may ignite. Extinguish all flames, burners, stoves, heaters and pilot lights and disconnect all electrical motors and appliances before use and until all vapors are gone. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. If sanding, wear a dust mask to avoid breathing of sanding dust. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. Avoid contact with eyes and skin. If you experience eye watering, headaches, or dizziness, leave the area. If properly used, a respirator may offer additional protection. Obtain professional advice before using. Close container after each use. FIRST AID: For skin contact, wash thoroughly with soap and water. If any product remains, gently rub with petroleum jelly, vegetable or mineral/baby oil then wash again with soap and water. Repeat as needed. Remove contaminated clothing. For eye contact, flush immediately with plenty of water for at least 15 minutes. Get medical attention. If swallowed, get medical attention immediately. If inhalation causes discomfort, remove to fresh air. If discomfort persists or breathing difficulty occurs, get medical attention. KEEP FROM FREEZING.
|
Notes
NA
|
|
