Product index
44020
|
Product number
TF9700
|
Product name
CONCRETE PRESERVATION COATING
|
Product group
1
|
Summary code
FL
|
Product description
TERMAFLURO TF9700 is a low-build elastomeric coating that provides the ultimate in reflectivity, color stability and weather resistance over new or existing concrete surfaces. Although it is highly flexible, it exhibits a tough, enamel-like finish that resists abrasion, biological growth, dirt, oil and all types of weather extremes. The Termafluro TF9700 is available in most colors and maybe pigment with heat reflective pigments to further enhance performance.
|
Uses
TERMAFLURO TF9700 is typically applied at the rate of 3 to 4 dry mils (76 to 102 microns). It is designed as a finish coat over a standard elastomeric acrylic basecoat, such as Termaqua TA6100, Termaqua TA 6010 Basecoat Termaqua TA 6080 Primer/Sealer which could be used to seal the concrete substrate.
Typical substrates include concrete ,concrete block., paving stones, etc. TERMAFLURO TF9700 is recommended whenever exceptional weatherability and/or reflectivity are required, whether the environmental threat is algae, mildew, dirt or industrial fallout. It also provides additional UV and color stability, even in bright colors. TERMAFLURO TF9700 is an excellent barrier to plasticizer migration. The natural fire retardancy of the film provides long-term protection, eliminating the need for additional additives that eventually migrate from the film.
|
Advantages
- Extreme Weatherability
- Applicator Friendly
- High Performance
- Excellent Stain Resistance
- Single Component
- Non Hazardous
- Single Coat
- Low VOC
- Superb Mill Dew Resistance
- Outstanding Water Repellancey
- Excellent Dirt Shedding
- Field proven performance
|
Chemistry + solvents
Waterbased Co-Polymerized Fluropolymer
|
System solvent
None
|
Color
Most standard architectural colors (maybe pigment with heat reflective pigments
|
Gloss
80-85° ASTM D523
|
Mix ratio
NA
|
Viscosity
100 KU
|
Solids by weight
45% ± 2% (depending on color) ASTM D2369
|
Solids by volume
31% ± 2% (depending on color) ASTM D2697
|
Density
NA
|
Volatile Organic Compounds (VOC)
185-195 grams per litre (depending on color)
|
Sag resistance
NA
|
Dry Film Thickness (DFT)
2 to 4 mils DFT 200 to 250 sq. ft./gallon (4.9 to 6.4 m²/l).
|
Spread rate
12.2 sq. m. per litre @ 25 microns DFT
497 sq. ft. per U.S. Gal. @ 1 mil DFT
|
Dry time
Approximately 6 hours @ 75°F (24°C) at 4 wet mils (100 microns)
|
|
Working pot life
NA
|
Performance data
Permeance ASTM D1653: <3 @ 2 mils Dry Film Thickness
Water Swelling - ASTM D471: <3%
Accelerated Weathering ASTM D4798: 1,000 hours = Pass
Wet Adhesion ASTM D903: >2.0 pli (350 N/m)
Fungi Resistance ASTM G21: Zero Rating
Tear Resistance ASTM D624: >250 lbf/in (87.5kN/m)
Flexibility ASTM D522 @ -15ºF (-26ºC): Passes 3/8" (1 cm) Mandrel Bend
Hail resistance: Passes FMRC moderate hail
Abrasion Resistance ASTM D968: 30 l/mil (25 microns) Falling Sand Test
Extended Accelerated Weathering. ASTMD4798/G155 or G154 UVB-313: 4,000 hours = Pass
Florida Weathering
G7 - 1 year:: Gloss retention per ASTM D523: >80%; Fade per ASTM D2244 AE<3.0 CIE units;
Chalking per ASTM D4214: 9 minimum;
Adhesion per ASTM D3359: 100%
|
Chemical resistance
NA
|
Surface preparation
All grease, oil, grime, and other contaminants must be removed from the surface using, commercial detergent or other suitable cleaning method All surfaces must be sound, free of cracks and ponding areas, dry, clean, and free of dirt, oils, curing agents, latence and grease. Moisture tests must be done to insure moisture content is below 15%.Use appropriate Termaclean Cleaner for the substrate being coated and appropriate pressure-washing techniques. Refer to additional information under the Surface Preparation section of the base coat technical data sheet. The base coat must be compatible with the underlying substrate as well as the TERMAFLURO TF9700 finish. Consult individual product data sheets for information on appropriate primers and base coats for individual substrates. The prepared surface must be analyzed for Chloride Nitrate and Sulfate content (Termarust has test kits available). Upper limit is per SSPC SP12-NV2.
|
Application
Apply a single coat of TERMAFLURO TF9700 at the rate of 200 to 250 sq. ft./gallon (4.9 to 6.4 m²/l). Contact Ternmarust Technical Service Department for additional information and requirements for specific product warranties.
|
Application equipment
NA
|
Compatible systems
Termaqua TA6100 Glassfilled Acrylic Roof Insulating Coating, Termaqua TA 6125 Insulating Coating, Termaqua 6200 Flexible Acrylic Crack Filler, Termaqua TA6010 Basecoat, Termaqua TA 6080 Primer Sealer
|
Thinning
NA
|
Clean up
Water
|
AGED ELONGATION
After 1,000 hours accelerated Weathering – ASTM D2370: >100% = Pass
|
WEIGHT PER GALLON
10.37 lbs/US Gal. ± .25%
|
ELONGATION
ASTM D2370: 148% (±50%)
|
TENSILE STRENGHT
|
Shelf life
12 months minimum in original unopened container when stored in a protected area where the temperature is between 5°C and 30°C (41°F - 86°F).
Note: After 12 months verify the coating to see if a skin has formed. If a skin is present remove skin and mix the material.
|
Safety precautions & regulatory data
Consult Material Safety Data Sheet for precautions. Product is water-based but may not comply with all state provincial or regional VOC restrictions. Avoid contact with skin and eyes. Avoid prolonged breathing of vapor. NIOSH approved respirator, eye & skin protection should be used by applicator and those in the vicinity.
Read label instructions carefully. This product is for industrial use only and is not intended for use in or around a household or dwelling.
*All films pigmented, data is formulation dependent.
|
Notes
NA
|
|
