Product index
45020
|
Product number
TA6125
|
Product name
GLASS FILLED ACRYLIC CONCRETE INSULATING COATING
|
Product group
1
|
Summary code
C-WB
|
Product description
Termaqua TA6125 is a glass filled, high viscosity, single component, air dry waterbased fast dry acrylic latex insulating coating. The product is specifically formulated to act as a insulation coating on concrete, metal, brick or stone especially in extremely hot climates as it attacks the substrate insulation problem with two elements instead of one. The color ( maybe formulated with heat reflecting pigments) as well as the high ratio of insulating hollow glass. The TA6125 has excellent UV resistance, color and gloss retention, flexibility, insulating properties and good corrosion resistance. Apply direct to existing coatings or properly prepared new substrates.
|
Uses
Termaqua TA6125 may be used to overcoat tightly adhere contaminate free coatings, to topcoat Termaqua TA6010 Basecoat, Termaqua TA6200 Flexible Acrylic Crack Filler or Termaqua TA6080 Primers. As a insulation coating it maybe used for both industrial and residential structures producing substantial savings in cooling costs. Application may take place over almost all materials including prepared metal, concrete, brick, stone and existing in place acrylic coating systems.
|
Advantages
NA
|
Chemistry + solvents
Deionized Water
|
System solvent
NA
|
Color
Most standard colors (heat reflect pigments available on request)
|
Gloss
Medium
|
Mix ratio
NA
|
Viscosity
112 KU
|
Solids by weight
51% ± 2%
|
Solids by volume
43% ± 2%
|
Density
NA
|
Volatile Organic Compounds (VOC)
.9 Lbs. / U.S. Gal
100 grams per liter
|
Sag resistance
NA
|
Dry Film Thickness (DFT)
10 - 20 mils DFT depending on amount of insulation value required. Value goes up with the thickness.
|
Spread rate
689.7 sq ft per gallons at 1 mil DFT zero loss factor
|
Dry time
TACK FREE: 1 hour
HARD: 3 to 4 hours
|
|
Working pot life
NA
|
Performance data
NA
|
Chemical resistance
NA
|
Surface preparation
NA
|
Application
The Termaqua TA6125 should be applied only when the air and product temperature is between ºF to 100ºF unless step are taken to slow the dry and the surface has been properly prepared. The surface temperature should not exceed 125°F during application.
|
Application equipment
Maybe applied with Spray, airless or conventional, roller, brush.
|
Compatible systems
Termaqua TA6080 Primer, Termaqua TA6010 Tan Basecoat, Termaqua TA 6200 Flexible Acrylic Crack Filler
|
Thinning
Brush/Roller: Not required. If desired reduce maximum of 15% by volume with Clean Deionized Water
Airless: Reduce up to 45 % by volume with Clean Deionized Water
Conventional Spray: Reduce up to 45 % by volume with Clean Deionized Water
|
Clean up
Use Clean water
|
GENERIC TYPE
Waterbased Glassfilled Acrylic
|
WEIGHT PER GALLON
10.03 lbs per gal. ± 2%
|
Shelf life
24 months in original unopened container when stored in a protected area where the temperature is between 5°C to 30°C (41°F to 86°F).
|
Safety precautions & regulatory data
Use with adequate ventilation. Avoid contact with skin and eyes. Avoid prolonged breathing of vapor. Read label instruction carefully and refer to Material Safety Data Sheet supplied. This product is for industrial use only.
Note: The technical data given herein has been compiled for your help and guidance and is based upon our experience and knowledge. It is subject to modification from time to time in the light of experience and our policy of continuous product development. Persons using this product must first satisfy themselves as to its suitability for the intended purpose. Please contact your sales representative for complete recommendations.
|
Notes
NA
|
|
