Product index
45030
|
Product number
TA6200
|
Product name
FLEXIBLE ACRYLIC CRACK FILLER
|
Product group
1
|
Summary code
C-WB
|
Product description
Termaqua TA6200 is a flexible, high viscosity, single component, air dry waterbased fast dry acrylic latex crack filler and butter coat. The product is specifically formulated to act as a crack filler and butter coat on concrete, most roofing materials, metal, brick or stone especially in extremely hot climates. It attacks the substrate repair problem with it’s unique ability to bridge and fill cracks and void areas up to two inches deep. The unique combination of resin and additives allow it to develop a very durable exposed surface while still retaining flexibility. The TA6200 has excellent UV resistance, flexibility, insulating properties and good corrosion resistance. Apply direct to properly prepared substrates.
|
Uses
Termaqua TA6200 may be used to overcoat tightly adhere contaminate free coatings, to topcoat Termaqua TA6010 Basecoat, Termaqua TA6200 Flexible Acrylic Crack Filler or Termaqua TA6080 Primers. As a insulation coating it maybe used for both industrial and residential structures producing substantial savings in cooling costs. Application may take place over almost all materials including prepared metal, concrete, brick, stone and existing in place acrylic coating systems.
|
Advantages
NA
|
Chemistry + solvents
Deionized Water
|
System solvent
NA
|
Color
Grey
|
Gloss
Medium
|
Mix ratio
NA
|
Viscosity
60,000 CPS # 6 at 10 RPM
|
Solids by weight
76% ± 2%
|
Solids by volume
65% ± 2%
|
Density
NA
|
Volatile Organic Compounds (VOC)
.9 Lbs. / U.S. Gal
100 grams per liter
|
Sag resistance
NA
|
Dry Film Thickness (DFT)
NA
|
Spread rate
1042.60 sq ft per gallons at 1 mil DFT zero loss factor
|
Dry time
TACK FREE: 1-2 hours
THRU DRY Dependent on thickness
|
|
Working pot life
NA
|
Performance data
NA
|
Chemical resistance
NA
|
Surface preparation
NA
|
Application
The Termaqua TA6200 should be applied only when the air and product temperature is between ºF to 125ºF and the surface has been properly prepared. The surface temperature should not exceed 125°F during application. Maybe applied with spatulas, trowels or poured int.
|
Application equipment
NA
|
Compatible systems
Termaqua TA6080 Primer, Termaqua TA6010 Tan Basecoat, Termafluro TF9600 and TF9700
|
Thinning
For Pour Applications: reduce maximum of 15% by volume with Clean Deionized Water
|
Clean up
Use Clean water
|
GENERIC TYPE
Waterbased Acrylic
|
WEIGHT PER GALLON
15.43 lbs per gal. ± 2%
|
RECOMMENDED THICKNESS
Apply up to 2 inches deep in a single application
|
Shelf life
24 months in original unopened container when stored in a protected area where the temperature is between 5°C to 30°C (41°F to 86°F).
|
Safety precautions & regulatory data
Use with adequate ventilation. Avoid contact with skin and eyes. Avoid prolonged breathing of vapor. Read label instruction carefully and refer to Material Safety Data Sheet supplied. This product is for industrial use only.
Note: The technical data given herein has been compiled for your help and guidance and is based upon our experience and knowledge. It is subject to modification from time to time in the light of experience and our policy of continuous product development. Persons using this product must first satisfy themselves as to its suitability for the intended purpose. Please contact your sales representative for complete recommendations.
|
Notes
NA
|
|
